The PG-M VHF 642 is a state-of-the art VHF linear power amplifier that covers 50MHz, 70MHz and 144MHz bands and provides 1000 W output power (PEP or continuous carrier) with less than 50W of drive.

The revolutionary TWIN topology offers ultimate flexibility for your radio station, transforming with a press of a button to match your desired configuration.
Combine the two modules into a single powerful amplifier, delivering 3500 watts of power in SO2R configuration.

The first 4O3A commercial amplifier. Continuous frequency coverage from 1 to 30MHz. Our TWIN topology provides guaranteed uptime through redundancy.If one out of the two RF modules fails for whatever reason, the amplifier will still remain on air uninterrupted, keeping half power through the second RF module. The damaged module can be hot swapped with a new one with absolutely no downtime.

An advanced engineering approach to tuner development has resulted in truly highest quality hardware and software solutions.

Optimize your antenna performance with the TGXL-O, a groundbreaking LAN-controlled automatic antenna tuner designed for installation directly at your antenna feed point – the ideal location for a tuner.

Antenna Genius is a smart antenna switch that features 8 antennas to 2 radios. Perfect for SO2R and multi-op contesting or making the most of your dual RX transceiver.

Antenna Genius is a smart antenna switch that features 8 antennas to 1 radio. Designed for less demanding applications.

OM module features 16 dual output relays and can be used with either the Antenna Genius 8x2, 8x1 or the Station Genius controller.

Rotator Genius is a smart rotator controller that uses a magnetic sensor for reading azimuth. It can be controlled by a Windows or Android app.

An affordable solution for anyone who doesn’t need the entire Rotator Genius system and wants the azimuth readout only.

USB to RS485 Converter. Supports Win, Linux, Mac OS, WinCE

This product is obsolete. Station Genius is a powerful station controler for complex switching. It’s designed for ease of use, versatility and expandability.

Transform your traditional radio into a cutting edge one. This accessory reads the CAT/CI-V band data from your radio and packs it into TCP/IP (LAN), making it a network CAT/CI-V server. Your radio can then integrate with any Genius device without worries.

Height: 4U, Width: 19"

This interface will convert frequency data given from RS232 CAT or CI-V to BCD output. BCD output can be used to control Antenna Genius or any other BCD controlled device.

These high-power (4,500 W ICAS) Band Pass Filters are to be fitted on the output side of your linear amplifier, filtering out not only harmonics but also broadband noise from the PA.

The 4O3A High Power HF Triplexer System Enables A Single Triband 20m/15m/10m Antenna (typically a Yagi) Fed With A Single Coaxial Feedline,To Be Used By Three Stations Running 4.5 kW simultaneously.

In order to meet the different needs and various setups of big stations we decided to put flexibility in to the foreground of our design. Instead of designing a simple Quadriplexer with four fixed band outputs we designed our Combiner QPXC-8, as an addition to the existing Triplexer System.

Eight antennas to two radios high isolation antenna switch.

Manual Antenna Controller S8 is an accessory in use with Antenna Genius, Antenna Switch 8x2 or Splitter PS3000RX.

A high isolation 6 antenna to 1 radio outdoor switch, with built- in high power CMC transformer, that can be safely installed at the bottom of your tower.

High isolation A to B switch, need for some applications such as extension of the antenna matrix.

The A50 switch is used as the 50 Ohm load for open ports on the HFC3000 combiner to prevent tuning degradation.

Due to the popularity of our A/B switches we decided to make a super-switch containing 8 A/B switches in a single box.

Lightning problems - a thing of the past! Introducing the first ever fully automated radio station protector. Fully automated it monitors your station and grounds all your antennas safely in cases of thunderstorms and more.

Power splitter can be used for splitting power between one, two or three antennas/directions, or for combining two or three antennas.

1A2R switch is a RF and PTT router which routes one amplifier between two radios. Switching is based on the PTT signal using the first one wins principle.

With the new reversible switch, you can easily exchange your amplifier and antennas in use in between two radios.

A controller for the RS3000 switcher. It makes sure that the switching can not be engaged while one of the users is transmitting.

Tower set, 36m high, Rhon 55

The second generation of open frame rings were developed as a solution to number of problems with classic rings.

Our rotary base comes with a preinstalled motor. You can choose between a single phase and three phase motor.

Towers are usually designed with 3m or 6m long sections, with standard width of 50cm, 60cm, 65cm, 80cm or 100cm.

PL-259, panel mount, plug

N-type male connector, panel mount

N-type connector 90°, for 5 mm cables. PTFE insulation.

(RG-58, RG-142...)

N-type connector 90°, for 10 mm cables.
PTFE insulation.

(RG-213,RG-214...)

N-type connector, for 10 mm cables.
PTFE insulation.

(RG-213, RG-214...)

PL plug, for 5 mm cables, 90° angle.
PTFE insulation.

(RG-58, RG-142…)

PL plug, for 10mm cables, 90° angle. 
PTFE insulation.

(RG-213, RG-214…)

PL plug for 10mm cables, with reducer for 5mm cables. PTFE insulation.

(RG-213, RG-214, RG-58, RG-142…)

NC-1 features Bluetooth 5.0 connectivity. In case your computer does not have Bluetooth capability we offer a verified tested dongle.

BTNC1R is designed for extended range use and features an external antenna.

This dongle does not come standard with the NC-1 headset.

NC-1 features Bluetooth 5.0 connectivity. In case your computer does not have Bluetooth capability we offer a verified tested dongle.

BTNC1 is designed for normal use within the same room.

This dongle does not come standard with the NC-1 headset.

The soft casing for transporting your MC-1 microphone as well as protecting it in storage.

This soft case comes standard with the MC-1 Microphone.

The soft casing for transporting your NC-1 headset as well as protecting it in storage.

The microphone sponge is not only a sibilance filter that ensures a nicer translation of your voice but a point of hygiene too. We recommend swapping the sponge for anyone else who
uses your headset.

The NC-1 headset comes with a two microphone sponge replacements.

The ear cushions are the most vulnerable and expendable part of any headphones. Securinga pair of backup ear cushions will extend the use time of the headset by years so securingsome spares might be a good idea.

Keep your NC1 Bluetooth Headset working like new and don't let worn out ear cushions diminish your comfort and listening experience on your NC1 Bluetooth Headset.

Most modern devices today feature a 4 pin TRRS (Tip Ring Ring Sleave) connector that hosts the two stereo headphone connections, a microphone connection and the ground.

In case you need to connect your headset to a device that has the headphone and the microphone connectors separated you will need this adapter.

This adapter is a 3.5mm TRRS male to 3.5mm stereo and 3.5mm mono female connectors so it can be used on the headphone output directly.

The adapter does not come as a part of the NC-1 headset and is sold separately.

The AI1 microphone adapter cable is created to adapt the MC1 microphone cable (which is a standard 3,5mm mono) to match the connector on your Icom radio.

The mic cable is plugged into the 3,5mm female mono jack on the adapter cable. The mic connector on the adapter cable then plugs into the microphone jack on your transceiver.

The 1/4 in. the female jack on the adapter cable is for connecting a Push-To-Talk (PTT) footswitch or hand switch. Even without a PTT footswitch or hand switch, your radio can still
be used in VOX mode.

The adapter does not come as a part of the NC-1 headset and is sold separately.

The AK1 microphone adapter cable is created to adapt the MC1 microphone cable (which is a standard 3,5mm mono) to match the connector on your Kenwood radio.

The mic cable is plugged into the 3,5mm female mono jack on the adapter cable. The mic connector on the adapter cable then plugs into the microphone jack on your transceiver.

The 1/4 in. the female jack on the adapter cable is for connecting a Push-To-Talk (PTT) footswitch or hand switch. Even without a PTT footswitch or hand switch, your radio can still
be used in VOX mode.

The adapter does not come as a part of the NC-1 headset and is sold separately.

The AY1 microphone adapter cable is created to adapt the MC1 microphone cable (which is a standard 3,5mm mono) to match the connector on your Yaesu radio.

The mic cable is plugged into the 3,5mm female mono jack on the adapter cable. The mic connector on the adapter cable then plugs into the microphone jack on your transceiver.

The 1/4 in. the female jack on the adapter cable is for connecting a Push-To-Talk (PTT) footswitch or hand switch. Even without a PTT footswitch or hand switch, your radio can still
be used in VOX mode.

The adapter does not come as a part of the NC-1 headset and is sold separately.

Carved from wood, specially designed to accommodate the NC-1 headset, this stunning stand will not only help protect your headphones, increasing their longevity, but will display them proudly and make your shack look more beautiful.

It’s a space saver: Cleans up any table, counter-top, or work space. It's great in your shack, on your TV cabinet, office, recording studio, bedsides the table or next to your computer.

It’s a beautiful piece of design: Made from wood, a beautiful natural material, this stand is a great looking accessory to keep your headset easily accessible. 

The headphone stand does not come as a part of the NC-1 headset and is sold separately.

The MC-1 is a versatile, affordable condenser microphone with superior vocal clarity. The MC1 delivers impressive performance with its wide frequency response. It captures your voice with exceptional clarity and precision.

For communication purposes, flat microphone response provides the possibility to be set with internal transceiver equalizer to fit your own taste and preference.

The microphone includes a convenient and beautiful soft case, 3.5mm to 6.3mm adapter and two sponges.

The MC-1 does not come as a part of the NC-1 headset and is sold separately.

Designed for Contesting
4O3A NC-1 is a top of the line headset designed primarily for contesting. We never found the perfect headset for our 4O3A station so we designed our own.
The NC-1 are light, comfortable and have amazing audio reproduction, making contesting a truly enjoyable experience.